Aluminum For Closures Caps 8011 H14 Manufacturer China
China is the world's largest producer and exporter of processed aluminum materials. Leveraging a comprehensive industrial supply chain and mature rolling technologies, China 8011 h14 aluminum for closure caps supplies more than half of the bottle cap manufacturers worldwide. As a core manufacturer specializing in aluminum for the packaging industry, Haomei Aluminum has focused on 8011-H14 aluminum for closures caps for over a decade. Our 8011 aluminum closure sheet products are used for bottle caps including alcoholic beverages, soft drinks, and pharmaceuticals—and are consistently exported to more than 30 countries and regions, including Southeast Asia, the Middle East, Europe, and Africa.

8011-H14 aluminum for closures caps is an Al-Fe-Si alloy designed specifically for packaging. We maintain precise control over the alloy composition starting from the casting and rolling stage: iron (Fe) content is kept stable between 0.6%–1.0%, and silicon (Si) between 0.3%–0.7%. Impurity levels are strictly regulated within national standard limits, ensuring an optimal balance of plasticity and strength from the very source. Haomei aluminum closure sheet products are manufactured using a fully continuous cold-rolling process, supported by an in-line, closed-loop thickness measurement system. We offer standard thicknesses ranging from 0.18 mm to 0.25 mm, with a thickness tolerance of ±0.005 mm for the entire coil, and a deviation of ≤0.003 mm between the beginning and end of the same coil. Through oriented grain rolling and multi-stage homogenization annealing, we achieve a stable earing rate of ≤2%. This ensures clean, uniform edges after deep-drawing, eliminating the need for additional trimming and increasing material utilization by more than 4% compared to the industry average. 8011 H14 aluminum closure sheets feature a stable tensile strength of 125–160 MPa, a yield strength of ≥110 MPa, and an elongation at break of ≥2%. With batch-to-batch mechanical property variance controlled within 5%, these coils are perfectly suited for high-speed, multi-station cap-stamping production lines operating at 800–1200 strokes per minute.
As an aluminum for closures caps manufacturer, we have implemented a comprehensive, end-to-end quality traceability system. Every batch—from raw material intake and rolling to annealing and final slitting—undergoes mandatory testing for mechanical properties, surface quality, and thickness precision. Our in-house laboratory is equipped to conduct specialized tests, including coating adhesion, salt spray resistance, and migration analysis for food-contact applications. Our products are ISO 9001 certified and comply with US FDA 21 CFR and EU DGCCRF standards for food-contact materials. We provide a full suite of multilingual test reports and compliance documentation to facilitate customs clearance and market entry worldwide.
With over a decade of industry experience, we have observed that the primary focus of bottle cap manufacturers has shifted from mere low pricing to supply chain stability and reliability; fluctuations in material performance between batches are the leading cause of production line downtime and waste. We once worked with a beverage cap manufacturer in Kenya that had cycled through three previous suppliers—all of whom struggled with inconsistent material strength, resulting in a stamping scrap rate consistently above 2.3% and monthly waste-related losses exceeding 10,000 dollars. After switching to our 8011-H14 aluminum for closures caps, the performance variance remained strictly within specified limits. This reduced the frequency of production line adjustments by 70% and lowered the stamping scrap rate to under 0.5%, allowing the client to recoup the cost difference in material procurement within just six months.
Regarding supply and service, we offer a variety of product configurations, including bare aluminum coils, single- or double-sided coated aluminum coils sheet, and pre-printed coils sheet. We can customize slitting widths based on your specific stamping press parameters, and we support coil inner diameters of 150 mm, 300 mm, and 508 mm. Our standard delivery lead time is 10–15 days, with dedicated production scheduling available for large-volume orders. We support various trade terms, including FOB and CIF, and our professional foreign trade team provides comprehensive, one-stop services covering customs clearance, logistics, and documentation.
Haomei Aluminum specializes in the precision manufacturing of aluminum for closures caps, serving global clients with consistent product quality and flexible supply capabilities. Whether you require bulk procurement of standard specifications or custom development based on specific parameters, please contact us for a complete selection proposal and quote.